Shaking table operating specifications:
Equipment inspection 1. Check the position of the vibration isolation mechanism; make the magnetic steel of the vibration table in a reasonable position;
2. Check if the signal excitation output line of the controller is reliably connected;
3. If the level test is carried out, turn the table body to the horizontal state and check accordingly according to the relevant contents of the equipment manual.
Installation of the test piece 1. Open the air pump and manually adjust the air pressure of the center airbag to the center position;
2. Fixtures and test pieces are installed in strict accordance with the requirements of the test task book;
3. The installation of the sensor room is strictly adhered to the requirements of the test task book and used as the designated purpose;
4. Connect the sensor to the controller channel specified in the test task book with the corresponding signal line;
Power-on sequence 1. Turn on the system power, make sure the gain switch is in the reset position, and close the power amplifier leakage circuit breaker;
2. Set the test parameters correctly according to the requirements of the test task and save them. If the test data is called, it must be checked whether the test settings are consistent with the test task book;
3. Press the power button and the fan will start. Open the gain knob to the appropriate position (refer to the instruction manual) / At this time, the “Prepareâ€, “Start†and “Power†lights are on, and the system enters the standby state.
4. Run the test, record the state of the test piece and the state of the test equipment in real time, and save the corresponding test data:
Shaking table use features:
1. Working temperature of vibration test bench: 5°C~35°C
2. Ambient humidity of vibration test bench: no more than 85% RH
3, electronic control, vibration frequency, amplitude adjustable, large driving force, small noise.
4, high efficiency, high load, high frequency width, low failure.
5. The controller of the vibration test bench is easy to operate, fully closed and extremely safe.
6, efficiency vibration type.
7, mobile work base frame, easy to place, beautiful and generous.
8. The vibration test bench is suitable for the production line and the assembly line for full inspection.
Equipment inspection 1. Check the position of the vibration isolation mechanism; make the magnetic steel of the vibration table in a reasonable position;
2. Check if the signal excitation output line of the controller is reliably connected;
3. If the level test is carried out, turn the table body to the horizontal state and check accordingly according to the relevant contents of the equipment manual.
Installation of the test piece 1. Open the air pump and manually adjust the air pressure of the center airbag to the center position;
2. Fixtures and test pieces are installed in strict accordance with the requirements of the test task book;
3. The installation of the sensor room is strictly adhered to the requirements of the test task book and used as the designated purpose;
4. Connect the sensor to the controller channel specified in the test task book with the corresponding signal line;
Power-on sequence 1. Turn on the system power, make sure the gain switch is in the reset position, and close the power amplifier leakage circuit breaker;
2. Set the test parameters correctly according to the requirements of the test task and save them. If the test data is called, it must be checked whether the test settings are consistent with the test task book;
3. Press the power button and the fan will start. Open the gain knob to the appropriate position (refer to the instruction manual) / At this time, the “Prepareâ€, “Start†and “Power†lights are on, and the system enters the standby state.
4. Run the test, record the state of the test piece and the state of the test equipment in real time, and save the corresponding test data:
Shaking table use features:
1. Working temperature of vibration test bench: 5°C~35°C
2. Ambient humidity of vibration test bench: no more than 85% RH
3, electronic control, vibration frequency, amplitude adjustable, large driving force, small noise.
4, high efficiency, high load, high frequency width, low failure.
5. The controller of the vibration test bench is easy to operate, fully closed and extremely safe.
6, efficiency vibration type.
7, mobile work base frame, easy to place, beautiful and generous.
8. The vibration test bench is suitable for the production line and the assembly line for full inspection.
Meltblown Cloth KN95 Face Mask
Kn95 Protective 3D Mask,Kn95 5 Layers Respirator,Meltblown Cloth Kn95 Face Mask,Kn95 5 Layers Fold Flat Face Mask
Jiangmen anjian biotechnology co. LTD , https://www.anjianmask.com