Introduction to small pellet machine
The rocking granulator can develop wet powder or lumps of dry material into the desired granules. The main feature is that the screen is easy to assemble and disassemble, and the elastic can be adjusted appropriately. The seven-corner drum is easy to disassemble and easy to clean. The mechanical transmission system is completely enclosed in the machine body, and a lubrication system is attached. The whole machine runs smoothly. The whole machine adopts stainless steel plate and conforms to GMP standards.
Small particle machine technical parameters:
Roller diameter (mm) 160
Effective length of the drum (mm) 360
Feed port size (mm) 410×430
Hob speed (rev / min) 55r / min
Production capacity 300-700kg/h
With power:
Motor power (kW) 3
Motor speed (rev / min) 1460
Voltage (volts) 380
Shape height (mm) 1240
Appearance length (mm) 950 × 750 × 1240mm
Machine net weight (kg) 480
Swing granulator instructions: Â
First , the scope of use
1. This machine is a kind of swaying action of a rotating drum. The wet powder material can be ground into particles by a wire sieve, and can also be widely used for pulverizing and becoming a ready-made granule.
2. In the case of chemicals, the powder is used as a wet-laid powder, and after drying, it is used to compress the tablet, and it is also possible to pulverize the block which is agglomerated during storage or agglomerated during chemical processing. It is used industrially to treat confectionery and sugar blends and malt milk, and other industries such as ceramics, plastics and the like into shaped pellets.
3. It is not suitable for semi-solid, fluid, slurry or wear.
Second, the basic characteristics
1. The machine is strong and powerful, easy to operate, stable in operation, and has a large bucket. The rotating drum is made of stainless steel to ensure that the quality of the treated material is clean and does not cause discoloration.
2. The mesh number of the mesh sieve should be self-prepared according to the particle size requirements. Its device is clamped with two steel pipes. It is easy to assemble and disassemble, and it is tightly supported by fine gears, which can be properly adjusted.
Third, the construction description
1. Main body: The fuselage is an independent rectangular cylinder. The upper bearing housing is connected with the powder bucket. The powder bucket extends to the outside of the machine. The V-shaped chassis is installed underneath. The ground is wide and flat, so the lower part must be installed. Can be placed indoors at will.
2. Granule manufacturing device: the rotating drum is placed horizontally under the powder bucket, and there are bearing supports on the front and rear. It is driven by the rack to make the reverse rotation. The front bearing cap of the end face is movable. The next wing nut, the bearing cap and the rotating drum can be extracted. The two ends of the roller are formed with a convex square ring embedded in the bearing chamber, so that the oil does not penetrate into the powder and does not stick.
3. Reducer: Adopt worm gear transmission, the speed ratio is 1:12. The oil can be stored in the box to ensure good gear lubrication and no noise. The mirror can be observed on the box, observe the operation and oil storage, and the outer end of the worm wheel. Equipped with an eccentric shaft to drive the rack to reciprocate.
4. Screen clamp tube: The device is made on both sides of the rotating drum, made of steel pipe, with a long groove in the middle, the two ends of the screen mesh are embedded in the groove, and the flower-shaped hand wheel is rotated to wrap the screen on the outer circle of the rotating drum. The gear wheel is supported by the gear wheel and can be adjusted by tightening.
5. Motor frame: one is bolted to the screw, and the motor is mounted on the iron plate. When the screw bolt is turned, the motor moves up and down to adjust the belt.
Fourth, the operating instructions
1. Usage: Start the machine and pour the mixture into the bucket. The rocking effect of the rotating drum will form particles through the wire mesh and fall into the container. If the crushing block is added, it should be gradually added. The pressure is too large and the screen is fragile.
2, Note: If the powder does not stagnate in the powder bucket, do not use the hand to shovel, so as not to cause injury, use bamboo shovel or parking work.
3, speed selection: due to the nature of the use of raw materials, so the speed of slow to choose, generally can be selected according to the viscosity of the material and the degree of dry and wet. The dry product is faster, the wet product should be slower, but the scope cannot be uniformly defined and should be determined by the user according to the actual operation.
Five, machine parts lubrication
1. The tank part of the machine is equipped with oil meter. It should be refueled once before driving. It can be added according to the temperature rise and operation of each bearing.
2. The worm gear box must store oil for a long time. The height of the oil surface is all invaded into the oil. If it is used frequently, it should be replaced with new oil every three months. There is oil plug at the bottom of the sputum.
3. When the machine is refueling, do not let the oil spill out of the cup, and do not flow to the surroundings of the machine and the ground. Because oil is easy to contaminate materials, affecting product quality.
Six, maintenance instructions
1. Check the machine regularly and check it once a month to check whether the worm gear, the worm, the bolts on the lubrication block, the bearing and other moving parts are flexible and wearable. The defects should be repaired in time and should not be used barely.
2. The machine should be used in a dry and clean room. It should not be used in places where the atmosphere contains acids and other gases that are corrosive to the body.
3. After the machine is used or stopped, the rotating drum should be taken out to clean and brush the remaining powder in the bucket, and then installed, ready for the next use.
4. When the drum moves before and after the work, please adjust the M10 screw of the front bearing to the appropriate position.
If the gear shaft is swaying, please adjust the M10 screw on the back of the bearing frame to the appropriate position, adjust the clearance so that the bearing does not sound, turn the pulley by hand, and tighten it properly. If it is too tight or too loose, the machine may be damaged. .
5. If the deactivation time is long, the machine must be wiped clean, the smooth surface of the machine is coated with anti-rust oil, and covered with a cloth.
Seven, installation instructions
1. This machine is packed in the whole box. After unpacking, move it to the appropriate place of use and use it after leveling.
2, the electrical circuit device: should pay attention to the direction of rotation, do not reverse, because the worm has a flat ball bearing at one end, the direction of the force must be on the bearing, otherwise it will cause damage to the other end of the worm, affecting the service life of the machine.
If you want to know more about pellet machine , please log in to our company : Or direct pharmaceutical process department : Consulting, our factory will provide you with more professional services!
2, the electrical circuit device: should pay attention to the direction of rotation, do not reverse, because the worm has a flat ball bearing at one end, the direction of the force must be on the bearing, otherwise it will cause damage to the other end of the worm, affecting the service life of the machine.
If you want to know more about pellet machine , please log in to our company : Or direct pharmaceutical process department : Consulting, our factory will provide you with more professional services!
We adopt mature formula process from German. It is suitable for pet at home, at pet hospital, pet clinical.
disinfectant is used to kill the pathogenic microorganisms on the transmission media, so as to achieve the harmless requirements, to eliminate the pathogenic microorganisms outside the human body, to cut off the transmission of infectious diseases, to achieve the purpose of controlling infectious diseases.
disinfectant, pet disinfectant, disinfector
Huali Technology Co., Ltd , https://www.jlhualitech.com